Jeju™ custom PMIC, engineered for Peak efficiency with 1.6T Optical DSPs - MaxLinear

November 18, 2026

How much power can you save on the DSP core rail in a 1.6T optical module?

In a compact OSFP or QSFP-DD module, power lost in conversion adds heat. With DSP core voltages below 1 V and high current demand, PMIC efficiency at the actual load points matters for the module’s power and thermal budgets.

MaxLinear designed its Jeju™ multiphase PMIC (MxL77904) for those low-voltage, high-current loads. The company reports up to 95% peak conversion efficiency and power savings of up to 0.5 W per 1.6T PAM4 DSP compared with conventional PMICs. Jeju is optimized for MaxLinear’s Rushmore 1.6T PAM4 DSP.

Custom-Designed for the Power Profile of 1.6T Optical DSPs
MxL77904 incorporates MaxLinear’s proprietary Constant On-Time (COT) power controller architecture, delivering fast transient response using conventional ceramic output capacitors without requiring external loop compensation. This enables tight voltage regulation with lower output capacitance, which can reduce component count, board area, and BOM cost.

Dynamic Voltage Scaling (DVS), controlled through I²C registers or GPIO interfaces, allows optical module designers to optimize power consumption and thermal load across operating states. Flexible 4+0, 3+1, 2+1+1 and 1+1+1+1 configurations, with up to 5A per phase, support a wide range of DSP, optical component, and module power architectures.

Key Benefits

  • Maximum efficiency at 1.6T DSP load points: Saves up to 0.5W per DSP compared with existing PMICs and delivers up to 95% peak conversion efficiency on low-voltage, high-current DSP core rails. Automatic phase shedding and phase adding, combined with Auto-PFM operation, reduce heat generation in thermally constrained modules.
  • Fast transient response with lower output capacitance: Maintains tight DSP rail regulation during dynamic load transients while reducing the required output capacitance and board area.
  • High DC and AC power accuracy to reduce dynamic power: Jeju’s 0.5% typical DC output-voltage accuracy, its high-resolution tracking output voltage steps, and tight control of overshoot and undershoot during load transients help reduce module-level operating voltage margin requirements and DSP dynamic power consumption.
  • Low-noise power delivery: Low-impedance integrated MOSFETs, programmable 600kHz to 4MHz switching frequency range, and remote voltage sensing support sensitive PAM4 DSP and optical analog circuitry.
  • Compact integration: Small 54-ball WLCSP package supports high-density QSFP-DD, OSFP, and future pluggable module designs.
  • Integrated protection: On-chip over-voltage, under-voltage, over-current, negative-current, short-circuit and over-temperature protection support the reliability requirements of data center optics.

Purpose-built for advanced 3nm and 4nm CMOS Optical PAM4 DSPs, Jeju is designed to deliver industry-leading peak power efficiency of up to 95% and power savings of up to 0.5W per 1.6T PAM4 DSP versus conventional PMICs. Due to its strong power-efficiency performance, Jeju is designed to reduce both module power consumption and heat dissipation, helping lower thermal management costs and improve overall module manufacturing yield. Jeju is optimized for MaxLinear’s Rushmore 1.6T PAM4 DSP and supports DSP-based 1.6T module designs across the industry.

As 1.6T and higher speed DSPs move to advanced 2nm, 3nm and 4nm CMOS process nodes, operating voltages continue to decline below 1V while current requirements increase rapidly. Conventional PMICs typically operate outside their optimal power-efficiency range and deliver poorer peak power-efficiency under the low-voltage and high-current operation requirements of advanced DSPs. This increases power loss and thermal burden within the constrained power budgets and space limits of OSFP and QSFP-DD optical modules. Jeju is specifically optimized for these requirements.

Expanding MaxLinear’s Optical-Module Platform BOM
The MxL77904 builds on MaxLinear’s heritage of custom power-management solutions for complex SoCs, including multi-rail, multiphase power architectures for broadband and connectivity platforms. Designed to broadly support DSP-based 1.6T modules, the MxL77904 expands MaxLinear’s data center component portfolio for optical modules beyond signal processing into optimized power delivery. Together with the Rushmore 1.6T PAM4 DSP, it brings MaxLinear’s expertise in signal processing, optical connectivity and power management to next-generation optical modules.

Evaluating power delivery for a 1.6T optical module?
Talk to TOP-electronics about your DSP rail requirements, load transients and thermal budget.

Back